Page History
1 Start process manager
In what follows, you
4 Develop a ship configuration and perform “design analysis’s”
We will configure a very simplified virtual ship design and perform all optional analysis’s analyses that are included in the knowledge base. It This should give you an a good impression of the process flow and will discuss most of the most common aspects that you will encounter when of performing a Quaestor analysis based on a Taxonomy approach. We will go through the whole process step by step as prescribed in the knowledge base Ship_configurator.qkb.
We assume you will start with a new project, as explained in chapter 1 Start a new ship configurator project. As mentioned, you need to have at least Domain Expert rights to be able to perform an analysis.
Please note that to use MS Word for report generation and MS Excel, make sure your security settings for MS Word and Excel are set correctly. If this is not done properly, you will get the appropriate messages from both MS Word and Excel. Contact the ICT department if you are not able to follow the instruction by Microsoft.
4.1 Start process manager
the taxonomy approach.
A new design configuration starts with opening the with opening the Process Manager by clicking .
- Click on the Process Manager Button
...
- . Click Yes when asked if you want to create a new solution and give it a meaningful name.
In this case only Ship configurator (= goal) is available.
Figure 6: Select a process with the Process manager
Select this task and press the button to start the process. Next Quaestor will request you to provide a name for your design configuration (a Taxonomy solution) for example “Test ship configurator”, see Figure 7.
Figure 7: Provide a solution title
After you have provided a solution title and continue, a tree structure is built in the tree of the Workbase starting with in which the first node (Entityentity) equal to has the name of your solution title. This is followed by an Entity "has a child Ship configurator” and this has a red Entity “child Ship design”.
Furthermore the list view (on the left) shows a value for "knowledge base version", see Figure 8.
Figure 8: Start screen after providing solution title
In other words, the ship configuration is started using Ship_configurator.qkb knowledge base version "1.0" (in this example) and the minimum required structure is built up.
...
.
2 Select process steps
An options window appears to select which shows the main available process steps you want to perform, see Figure 9.
Figure 9: Options window; select the process steps . You can select those that you want to performIf you want go through all process steps you have to :
- For this tutorial, select all of them and click OK.
(recommended for this tutorial). Please note that you can also decide to carry out only a part of the analysis process steps. When you want to add other steps later, simply go to the Entity “Ship configurator”, press the "Accept input & Continue" button select the entity Ship configurator, press Ctrl+F5 and the options window will reappear.
Please note Quaestor automatically checks dependencies between process steps. For example, select “Intact “Intact stability calculation” calculation” only. Now Quaestor automatically selects “Mass calculation” because “Intact stability calculation” “Mass calculation” because “Intact stability calculation” apparently requires information from “Mass calculation”“Mass calculation”.4.3
3 Select optional
...
entities
After selecting the process steps (for this tutorial we assume you have selected all) some Entities , some entities are added to the tree structure in thetree view. Moreover, the Entity “Lay out” is in focus and another option box appears. The number "2" behind Entity name “Lay Out” indicates two optional Entities are available below Entity “Lay out”. Now, you can select the optional Entities “entities Decks” and “Bulkheads” as a child of Entity “Lay Out”, see Figure 10. Please select “Decks” and “Bulkheads” and press “Ok”.
Figure 10: Selected process steps are presented in tree structure
Please note; after selecting both optional entities the number "2" behind Entity name “Lay Out” is not visible anymore. By pressing each plus sign (for instance in front of Ship design) you can open the tree structure and use the minus sign to close it.
4.3.1 Entity colors
During a dialogue Entities can have three kinds of colors, each with their own meaning:
...
Bulkheads.
- For this tutorial, select both of them and click OK.
When you have selected the options Decks and Bulkheads, both entities are added below entity Lay out.
| Info |
|---|
Entities can have one of three colors:
|
...
|
...
|
...
|
...
|
...
|
...
|
...
|
4.3.2 Navigate through process
4 Navigate processes
As soon as you start At the same time you started a new solution, the process buttons change their status and names. When you press click the active buttons "Accept input & Continue" and "Stop Process", this is exactly what will happen. When you press the "Stop Process" button, the process is stopped. Press "Restart Process" button to restart your solution. To start the process at a given position, select this position and press the "Restart Solution here" button, etc.In the overview you also see the "Calculate" button. Pressing this button, button Next, the next input is asked. Stop input does just that. There can be other actions mentioned as well. There is now also a Calculate All button. When you click it, Quaestor will try to calculate all blue Entities entities within your solution.Please note that, to
| Info |
|---|
To perform an analysis, carry out changes, etc. the Quaestor process has to be started by clicking Data input. The process is active when the |
...
Next button is shown and stopped when the |
...
Data input button is shown again. |
In Generalgeneral, performing working through the process is very straight forwardstraightforward. You can provide input values that are presented in the Workbase either in white or light blue and pressing the "Accept input & Continue" button (or press the Enter button)click Next. You are guided in a “logical sequence” through the whole conceptual design process (for this Ship configurator) as developed by the knowledge engineer (the developer of the knowledge base).Please note that you
| Info |
|---|
You can always decide to carry out only part of the conceptual design steps or provide the input in a different order. Just go to the |
...
pertaining parts in the tree and continue. Any relation between necessary input and steps in the process is taken care of by Quaestor. In other words, when input is required, it will eventually be requested. Furthermore, it is shown by the colors of the |
...
entities. |
...
5 Provide input values
...
When you have selected the options “Decks” and “Bulkheads”, both Entities are added below Entity “Lay out”.
Now, Entity "Main Dimensions" Now, entity Main Dimensions is in focus and input values are requested in the list view, see Figure 11. :
| Info |
|---|
| A white cell means that input values from the user are needed. |
...
| Info |
|---|
| While scrolling through the parameters in the list view, the Explanation window shows the descriptions and explanations for the selected parameter. |
Once an input value is given, the cell color changed changes to light blue. You are can always able to change your input values later on.
Figure 12 shows example input values for Entity “Main Dimensions”.
Figure 11: Provide input values for Entity “Main Dimensions”
Figure 12: Example input values Entity “Main Dimensions”
4.5 Provide input values for Entity Hydrostatics
After completing Entity “Main Dimensions” press “Accept & Continue” to accept your input values. Hereafter Entity “Hydrostatics” is in focus, see Figure 13.
- Enter input values as shown here and click Next:
Now, entity Hydrostatics becomes selected in the tree:
Figure 13: Provide input values for Entity “Hydrostatics”
You see that yellow and white cells are shown. A yellow cell means that a value is a top Top Goal for the analysis (inside the Entityentity) and it will be determined by a relation. For example, select “Lpp” in the Entity (shown in Figure 13) and you can see that the value 120 is value is computed by means of the relation Lpp = Entiy#Entity#(20).Lpp, as explained shown in the Explanation window on the leftright.
When If you do not have the explanation part “Computed in solution by:”, please go to the Explanation tab of the Options windows (Tools>Options…) and select the “Requested select Tools > Options > Explanation and check Requested by/determined by” optionby.
A Knowledge Engineer can define a minimum and/or maximum value for a parameter. Quaestor will issue a warning if the computed or input value exceeds the indicated boundaries. For example provide
- Enter value
2for parameterCb
...
- and press Enter.
A warning message appears, telling you that Cb should be between 0 and 1. After you click OK, you will see that the value does get accepted anyway!
- Enter input values as shown here and click Next:
Figure 14: A Knowledge Engineer can define a minimum and maximum value for a Parameter
Example values for Entity “Hydrostatics” are given in Figure 15.
Please note that the resulting value for parameter “Volume” is presented as a light blue cell, which is the default color to present an input value. AlthoughHowever, this parameter is calculated by ; Volume = Cb*Lpp*Boa*T_design, as you can see when you select the parameter and look in the Explanation window (see Figure 15). The reason is, that parameter “Volume” is defined as a special proposed value, which can be edited after calculation. When you modify the proposed value, the cell will turn red in order to indicate that a proposed value is modified. To return To return to the proposed value again, select value again, select the value and press the space bar to delete the value and press enter. Now the proposed value is calculated and shown again in light blue.
Figure 15: Example input values Entity "Hydrostatics"
...
6 Define the reference planes
For the ship configurator, it is decided to define reference planes first, these . These can then be used to locate other objects like Decks and Bulkheads in a ship design, and then define the arrangement itself. The moment Whenever you change a value of a single reference plane, Quaestor propagates the changed value through the whole solution. Therefore, using reference planes is a powerful method to develop a parametric design.
After leaving the Entity “Hydrostatics”, Entity “Transverse planes” Now, entity Transverse planes will be in focus, see Figure 16selected in the tree. The definitions of reference planes and the coordinate system of the vessel are depicted shown in the Explanation window by with a schematic picture. The picture size can be in- or decreased changed by resizing the Explanation window. The default proposed value of parameter “Frame_spacing” is 700 [mm], which can be modified. You have to provide the number the number of transverse reference planes you planes you want to add to your solution, please provide 3.
Figure 16: Transverse reference planes
- Enter 2 as the number of transverse reference planes and press Enter. Select New empty Case(s) from the window that pops up after this.
Now a table of 2 Next a table of 3 columns is created in the table view, each representing a transverse reference plane. You have to provide a frame number and a name for to enter a frame number and a name for every plane (any recognizable name will do). Quaestor will calculate the X position of the X position of a transverse reference plane by X = Frame_nr * Frame_spacing. Figure 17 shows example input for Entity "Transverse planes".
Figure 17: Example input values Entity "Transverse planes"
4.7 Define horizontal reference planes
The same procedure for defining transverse reference planes is developed for the horizontal reference planes. Figure 18 shows example input for Entity "Horizontal planes".
Figure 18: Example input values Entity "Horizontal planes"
4.8 Define number of Decks
- Enter input values as shown here and click Next:
The horizontal reference planes will be defined by the same procedure.
- Select entity
Horizontal planesin the tree. - Enter 2 as the number of horizontal reference planes and press Enter. Select New empty Case(s) from the window that pops up after this.
- Enter input values as shown here and click Next:
7 Define decks and bulkheads
You have selected optional entity Decks, so When you have selected optional Entity “Decks” (in chapter 4.3), you have to indicate the number of “Deck” Entities entities you want to include, Figure 19, that will automatically be placed below Entity “. These will be automatically placed below entity Decks. In this tutorial we define two decks, so Number of decks = 2.
Figure 19: Provide number of Deck Entities
we need two decks.
- Select entity
Decksin the tree. - Enter 2 as value of the
Number of decksand press Enter.
Next you have to define a name and a deck function for every deck. A deck function can be selected from a drop down box. To locate a deck within your ship design, you have to relate the aft and front position of a deck to one of your defined transverse reverences planes and the height of a deck to one of your defined horizontal reference planes. You can refer to your defined reference planes by selecting one of your defined reference names that will be shown in a drop down menu. Figure 20 shows example input values for the first Entity "Deck".
As you can see in Figure 19 the total accommodation deck area will above, the total accommodation area will be computed at the level of Entity “entity Decks”. The total Total_accommodation deck _area will be results from the summation of all areas of Decks with Deck's, using the Deck_function$ parameter equals to accommodation. In the second part of this tutorial it will be explained how this can be developed. named 'Accommodation'.
- Select the first entity
Deckin the tree. - Enter input values as shown here and click Next:
For the second deck the same parameters are requested, example input is given in Figure 21. Here, another Deck_function$ is used. Please note that the Entity in the mean time, the entity node name in the tree view of the tree view of the first deck is changed into a more recognizable name than just “Deck” Deck. Now the Entity entity node name of the first Deck contains the name of the deck and the deck height.
Figure 20: Example input values first Entity "Deck"
Figure 21: Example input values second Entity "Deck"
...
- Select the second entity
Deckin the tree. - Enter input values as shown here and click Next:
- Select entity
Bulkheadsin the tree.
This ship configurator uses a different Entity an entity structure for defining (transverse) bulkheads in comparison with defining decks from the previous paragraphthat differs from the one used for the decks. Of course, the same Entity entity structure could be used, but it is more instructive to present (and develop in the second part) a different presentation form. First, you have to provide the number of bulkheads you want to include in your ship design.
- Enter 2 as the value for
Number of bulkheadsand press Enter. Select New empty Case(s) from the window that pops up after this.
Now . In this tutorial we define two bulkheads. Next a table of two columns is created in the table view, each representing a singular bulkhead. No further explanation is needed to provide input values for an Entity “Bulkhead”. After completing Entity “Bulkheads” the ship lay out is completed. Figure 22 shows example input values for two defined bulkheads.
Figure 22: Example input values Entity "Bulkheads"
4.10 Mass calculation
If single bulkhead. After completing entity Bulkheads the ship lay out is finalized (it is always possible to change values afterwards) the first analysis, Mass calculation, can be performed. Figure 23 presents Entities below Entity “Mass calculation”. In here the mass and the centre of gravity of the whole system will be calculated, which depends on the mass and centre of gravity of both light ship weight and weight of cargo objects. The total mass is calculated by the summation of all mass components. The centre of gravity of a system of components is defined as the average of their positions, weighted by their masses. This method is used at every level within the Mass calculation.
Figure 23: Tree view mass calculation
At the level of Entities “Mass Calculation”, “Light ship Weight” and “Mass Cargoes” no input is requested to the user. So click “Accept input & Continue”. Quaestor calculates all information in these Entities when all required information from lower Entities is available.
4.11 Provide input values for Entity Mass Hull
Based on the results of Entities “Main Dimensions” and “Hydrostatics” below Entity “Hull” the centre of gravity and volume of the hull is determined. Scroll through the parameter list to see the used relations in the Explanation window. For this simplified ship configurator we assume that the mass of the hull can be computed by:
Mass = Weight_volume_factor* Volume
As user you only have to provide a weight volume factor, for example 0.5 [t/m3], see Figure 24. The moments around the X, Y and Z axis are determined by Mass multiplied by respectively COGX, COGY and COGZ.
Figure 24: Example input Entity "Mass hull"
4.12 Mass calculation of Decks and Bulkheads
In section 4.8 you already defined the names and positions for a number of decks; in this tutorial two decks were defined. Entity “Decks”, below Entity “Mass Decks”, presents a table, containing for each defined Deck; the deck name, the (deck) area and the centre of gravity, see Figure 25.
Figure 25: Provide weight factor for every deck you have defined
Again, a yellow cell means that a value is a top Goal for the analysis and it will be determined by relations. The parameters “Nr”, “Name of deck”, and “Area”, are automatically copied from the defined “Deck” Entities below Entity “Lay out”. When you add or remove a deck, or change properties of an existing defined deck, these adaptations will automatically propagated to the “Mass Decks” Entity.
The centre of gravity of a deck is based on the given location in your ship design. For this simplified ship configurator we assume that the mass of the decks can be computed by:
Mass = Weight_area_factor* Area
As user you only have to provide a weight area factor for each deck, for example 0.02 [t/m2] and 0.03 [t/m2]. The mass calculation as applied for decks is also used for the mass calculation of bulkheads. Figure 26 shows example input for Entity “Bulkheads” below Entity “Mass Bulkheads”.
Figure 26: Example input values Entity "Bulkhead" below Entity "Mass Bulkheads"
4.13 Define number of cargo objects
Besides the light ship weight calculation it is possible to define the name, COG and mass of a number of cargo objects. Further explanation is not needed. Example input values are given in Figure 27. Please note a schematic picture in the Explanation window depicts the vessel coordinate system as support for the user.
Figure 27: Example input values Entity "Cargoes"
4.14 Intact stability calculation
The mass and centre of gravity of the whole system are input for the intact stability calculation. For this tutorial a very unrealistic simplified stability|Co calculation is developed. The moment of area inertia of the waterline area is the only required input value.
Entity “Intact stability” is only included to give an idea how a configurator can be build with a taxonomy approach. Example input values for Entity “Intact stability” is presented in Figure 28.
Figure 28: Intact stability calculation
4.15 Data to Word report
At the moment you leave Entity “Intact stability” with the "Accept input & Continue" button Quaestor jumps automatically in Entity“Data to Word report”. In here you do not have to provide any input values. Quaestor will directly generate (if all information from the previous Entities is available) a little MS Word report. When you have this document open at that moment, you will see the generation of the reports on your screen.
Please be aware that fatal errors may occur when you are actively working in Word while the reports are generated. Therefore, please wait until the documents are closed.
There are two ways to open the created Word documented from inside Quaestor.
- Select the parameter Report_document$ in Entity “Example report” and click on “Click here for value” in the Explanation window below “Name, value & dimension”.
- Double click on the report name behind the parameter Report_document$ (in Figure 29 “Report_151212_2.doc”).
Finally, it is always possible to find and open the document in your project folder on your computer. The example report document is built up from two sub documents (two chapters) that also can be watched / opened separately.
Figure 29: Generation of example MS Word report
4.16 Data to Excel
The main dimensions and a table of deck data will also be written to an Excel file. In here the total deck area will be calculated and the result will be send back to Quaestor in parameter “Total_deck_area”, see Figure 30. If Quaestor knows all the required data the Excel file will be made at the moment you are in Entity “Data to Excel”.
Please note that the knowledge engineer (the developer) can decide whether to leave the Excel sheet (or Work document) open or close it automatically. In the case of the Excel sheet it has been chosen to leave the Excel sheet open.
There are two ways to open an Excel file from Quaestor.
- Select the parameter File_name_Excel$ in Entity “Data to Excel” and click on “Click here for value” in the Explanation window below “Name, value & dimension”.
- Double click on the Excel file name behind the parameter File_name_Excel$ (in Figure 30 “Deck_data_153402.xls”).
Finally it is always possible to find and open the document in your project folder on your computer.
Figure 30: Data to Excel
completed.
- Enter input values as shown here and click Next:
...
Back to content | << Previous | Next Back to content | Back to Explanation user interface | For knowledge engineers: Continue with the tutorial on the creation of a Taxonomy type knowledge base >>
Overview
Content Tools